Absorption, Reflection, Reduction and Flanking

Share This Post

Share on linkedin
Share on twitter
Share on facebook

When sound energy hits a flat surface one (or more) events will take place depending on what the surface is manufactured or constructed from.
Porous materials such as open cell foam or mineral fibre will provide absorption that assists in controlling reverberation.
Most surfaces will allow sound to bounce off (or reflect) back in to the space that again increases reverberation or can affect the balance of the room where uses include the need for critical listening etc.
Sound reduction is the process of adding mass to a system to prevent sound from travelling from one area to another (such as a wall). These materials are solid and can be in the form of a single material (sheet of plasterboard) or a composite material that offers both mass and absorption (wall with plasterboard both sides and a cavity containing mineral fibre).
Flanking transmission is created where sound bridges or bypasses the acoustic material or construction, usually as a result of gaps or weak spots within the installation or construction.

These four principles are shown in the diagram below:

Absorption – Highlighted by the red arrows, the sound energy passes into the material where some energy is converted in to heat and the remaining energy then bounces back into the room. If the material is hanging in free air then the sound energy may pass through the absorber instead of reflecting back in to the room.

Reflection – Where a hard surface such as glass is encountered the sound energy will bounce off this and radiate back into the room (as shown by the blue arrows) without the loss of any energy causing reverberation.

Reduction – If a mass layer such as plasterboard or concrete is used then this will prevent sound energy from freely passing through and the sound levels within the receiving room will be lower than that generated by the noise source (green arrows). The level of sound reduction will depend on the mass of the material used as well as the construction method used.

Flanking Transmission – This is the act of sound travelling around, or bridging, a building element by exploiting a weakness in the material, construction or installation (magenta arrow) and therefore rendering the acoustic treatment redundant.

When looking at designing acoustic solutions it may be necessary to include more than one of the above principles to achieve required performance levels. For example, when building lightweight internal partitions the use of mineral wool within the cavity not only provides the required thermal properties but also acts as an absorber for sound energy that passes through the plasterboard initially.

More To Explore

Building Acoustics

Absorption, Reflection, Reduction and Flanking

When sound energy hits a flat surface one (or more) events will take place depending on what the surface is manufactured or constructed from.Porous materials such as open cell foam or mineral fibre will provide absorption that assists in controlling reverberation.Most surfaces will allow sound to bounce off (or reflect)Read More

Sound meter and tripod for measuring sound pressure levels
Building Acoustics

The benefits of good acoustics

What and Why? Acoustics are an integral part of many different building types and designs, and usually, just the bare minimum is undertaken to meet statutory requirements without any consideration as to why the acoustic package has been included within the overall specification.Part of the reasoning behind this may haveRead More

Wall & Ceiling Materials
Building Acoustics

Sound Insulation for Partitions

The topic of sound insulation within acoustics can be a complicated subject for a variety of reasons including terminology, the sector it is being applied to, standards and rating values. At AEI Acoustics we want to help you understand the subject easier, for the specific sector you are concerned aboutRead More

Wall Panels
Building Acoustics

Treating Reverberation

I was recently talking to a member of the site team on a new school build with regard to the acoustic package required in each room and as normal (in my experience) the first topic raised was “why do we need it?” Once this had been explained the next statementRead More

Industry News

AVO Guide, January 2020

In January 2020 the ANC (Association of Noise Consultants) and the IOA (Institute of Acoustics) jointly published the long awaited Acoustics, Ventilation and Overheating Guide (AVO Guide) to provide professionals within the acoustic industry (as well as architects and other professionals engaged in the planning, design and commissioning of newRead More

Company News

Open For Business

2020 has proved to be a most eventful year for every person around the globe and one that will not be forgotten quickly. January saw the threat of Covid-19 escalate quickly with events in China starting to be felt in Europe and industry began to formulate plans on how toRead More

Interested in finding out more?

Contact us for a free consultation today

Design and Specification

Need Help?

WE are Here To Assist You

Need a free consultation?

Contact us for advice and assistance 

Thank you for requesting our CPD on Acoustics in Education

Please let us know what you think

Need additional certificates?

Forward on the details and we will do the rest

dealing with Covid-19

At AEI Acoustics we understand the importance of keeping safe in this period of uncertainty we are now required to operate within.

Whilst complying with government guidelines we also aim to meet any extra requirements you may have in place within your company or organisation.  Should you have any particular protocols in place that we need to follow please make us aware at the earliest possible opportunity to ensure we can comply with these.

Within our own company we undertake a continual risk assessment process to ensure we are operating within the government guidelines and understand the importance of limiting contact wherever possible. We are happy to undertake meetings in person however where these can be undertaken through digital means, such as a Zoom or Skype, we believe that this should be the preferred choice to limit the risk of transmission.

Where site visits are required we will ensure that we use appropriate PPE and observe social distancing measures.  If any member of staff shows signs or symptoms of Covid-19 they will not attend site and will self-isolate along with those they have been in contact recently.

Please contact us directly if you require to discuss this any further or book our services by clicking here.